亚洲 欧美 图片 自拍 视频

<em id="7lnzx"></em>

    <pre id="7lnzx"></pre>

        <strike id="7lnzx"><address id="7lnzx"></address></strike>

        <big id="7lnzx"></big>

          How to configure the power amplifier to achieve the best state

          To some extent, the power amplifier dominates whether the whole system can provide good sound quality output.

          For many friends, they do not know the amplifier very well. It is unclear which accessories are needed to configure the amplifier speakers in order to play the effect of the amplifier to an optimal state?

          The first one is to install a resistor under the speaker for current sampling. Actually, the voltage signal is fed back. It is analog current feedback. The most people do it, but this circuit is defective. There are two reasons.

          1. It is because his output gain will change with the change of impedance. As a result, the constant voltage is not applied to the end of the horn 2, as if the power applied to the horn can be made constant.

          But do na€?t forget, the sound pressure characteristic curve of the speaker is TEST under the constant voltage output, so this kind of circuit is not good, the hearing is not good, it is fun, but there is an improved circuit that uses negative voltage feedback Mainly, adding an appropriate amount of this type of current negative feedback can make a good sound, but at this time, the role of current negative feedback is to change the damping coefficient of the power amplifier, which has little effect on the amplitude-frequency characteristics.

          2. The sampling point is below the horn. The horn is an inductance. The phase of the current flowing through the inductance will change. The low frequency is good, the high frequency can be shifted by 90 degrees, and the phase characteristics are extremely poor.

          The second type: negative resistance amplifier, except for some special occasions, the first one used for audio and achieved success is YAMAHA. Its main role is to improve the extension of low frequencies, but it is for 200Hz or more. Frequency will play a role in degrading sound quality, so it is generally used in ultra-low frequency active speakers.

          In fact, this circuit is used in conjunction with the speaker, there is no practical significance alone. Its working principle is: if the speaker is a rigid body, then adding a tube can turn it into an ideal Holmuz resonance box, then regardless of the size of the box, the thickness of the pipe, as long as it conforms to the Holmuz resonance Calculation formula. Even the resonance point of 20Hz can be achieved. The size of the box is just the efficiency. Due to the presence of the speaker on the speaker, the speaker is moving when it sounds, the speaker is not a rigid body, then the box will not produce Holmoz resonated.

          Therefore, if the horn's diaphragm is stationary while sounding. Then, the box is close to the rigid body, which can meet the conditions of Holmoz resonance, and the resonance point of this box can be arbitrarily designed. The job of keeping the horn untouched when speaking is the task of the negative resistance amplifier. The working principle of the negative resistance amplifier is that when the horn is working in the low frequency band, its impedance characteristics change sharply. The amplifier circuit uses the current sampling to take out this change and feed it back to the power amplifier. By performing equivalent analysis on the circuit, it can be found that the internal resistance of the power amplifier becomes a negative resistance characteristic in calculation.

          During dynamic amplification, the internal resistance of the speaker plus amplifier is close to zero. As a result, this kind of circuit makes the speaker be strongly damped in any direction. As soon as the sound ends, the horn will not move and the box will become rigid.

          The third type: current mode feedback amplifier circuit, this is a practical current amplifier circuit, and it is also a real current type negative feedback. The feedback signal is current, not voltage, that is, it is not added at the negative feedback terminal, but added , Current flows in. This kind of circuit was first used in video transmission, or instruments and equipment like an oscilloscope or something.

          Due to the excellent high-frequency characteristics of the low-impedance negative current feedback input circuit, the driving capacity of the capacitive load is super strong. As long as the improvement is made, it is found that it is very good to make a power amplifier, which can make up for some of the inherent shortcomings of the voltage amplifier, like The open-loop frequency response is low, the closed-loop transient frequency response is distorted, and the drive capacity of the capacitive load is extremely weak. The disadvantage is that the open-loop gain of this circuit is relatively low, and the distortion after the closed loop will be an order of magnitude higher than that of the voltage amplifier.

          However, if you do well, the total distortion will not exceed 0.01%.

          Plastic Coated Electric Kettle

           

          The original stainless steel double wall Electric Kettle. This kettle comes with 100% stainless steel interior. Outside made by plastic for protect your hand in case that the hot stainless steel will scald your hand. No plastic in contact with hot water. The spacious kettle has a volume of 1.8 liters which give ample space to boil tea, coffee or soups in minutes. Lets you boil a huge quantity of liquid at a time and helps save time and electricity.

           

           

              Stainless Steel Body With Plastic Outside: Ergonomic in design, the electric kettle has a sturdy handle with smart contours to make your grip a firmer one. The stainless steel finish gives a glossy feel and boasts a rust-free performance. This stainless electric kettle comes with a convenient spout so that liquid can be easily poured from it directly into a container. It avoids any spillage and thus prevents your kitchen from getting messy.

              360 degree rotational body with separated base: Enjoy the ease and convenience of cord-free serving with this stylish stainless steel kettle. Perfect for placing on the table for gatherings or leaving on the base for worry-free hot water any time of day.

             Automatic shut off when water boils or dry: This overheat safety protection feature of the electric Kettle helps to prevent hazardous accidents. The cordless electric kettle switches off if the water inside the kettle dries up. It also saves on electricity as it uses very less power.

             Lightweight and Portable: Carry your kettle anywhere to enjoy a warm cup of coffee or tea away from your home. Kettle not only looks good but maintains a high standard in terms of durability. Lightweight and its small dimensions snugly fit in your bag. Portable and small in size, this electric kettle makes a perfect travel companion.

             Cool touch Exterior: With out cool-touch design. You`ll be able to touch the outside of the kettle even when it`s boiling. There`s no risk of getting accidentally burnt, so it`s perfect for homes with young children.

           

           

          Application:

          Enjoy your coffee.

          Cook egg for morning.

          Boil some lemon tea

          Plastic Coated Electric Kettle

          Plastic Coated Electric Kettle,Household Plastic Kettle,Colorful Water Kettle,Auto Shut-Off Electric Kettle

          Guangzhou Taipeng Electrical Appliances Technology CO., LTD. , https://www.taipengelectric.com

          亚洲 欧美 图片 自拍 视频
          <em id="7lnzx"></em>

            <pre id="7lnzx"></pre>

                <strike id="7lnzx"><address id="7lnzx"></address></strike>

                <big id="7lnzx"></big>