亚洲 欧美 图片 自拍 视频

<em id="7lnzx"></em>

    <pre id="7lnzx"></pre>

        <strike id="7lnzx"><address id="7lnzx"></address></strike>

        <big id="7lnzx"></big>

          Fuji inverter troubleshooting and maintenance

          Fuji inverter maintenance and troubleshooting (1) 1, OH2 alarm and OH2 alarm For G/P9 series machines, because there is an external alarm definition exists (E function), when this external alarm definition terminal does not have a short clip or in use When this short-circuiting chip is virtually connected, it will cause OH2 alarm; if the CN18 plug-in (temperature detector plug) is loose at this time, it will cause a€?1, OH2a€? alarm and cannot be reset. After the inspection is completed, it is necessary to restart the power supply for reset.

          (2) Low-frequency output oscillation failure When the inverter outputs at a low frequency (below 5Hz), the output/reverse direction of the motor output frequently pulsates. Generally, the inverter's main board has a problem.

          (3) Oscillation fault in one acceleration zone When the inverter appears in the low-frequency three-phase imbalance (expressing motor oscillation) or oscillates in a certain acceleration interval, we can try to modify the carrier frequency (decrease) of the inverter. Solve the problem.

          (4) Operation without output fault This fault is divided into two cases: First, if the LCD display shows the output frequency and voltage rise after the inverter is running, and the measurement output has no voltage, the driver board is damaged; second, if the inverter is running, The output frequency and voltage displayed on the LCD monitor always remain at zero, which is a problem with the motherboard.

          (5) The running frequency does not rise Fault: When the inverter is powered on, press the run button, the operation indicator is on (keyboard operation), but the output frequency always shows "0.00" does not rise, generally the driver board has a problem, change the block After the new driver board can solve the problem. However, if the inverter is able to rise to the set frequency during no-load operation and stays at about 1Hz with the load, it is because the load is too heavy, and the a€?instant overcurrent limit functiona€? of the inverter is activated. At this time, it is modified. Parameter solving; such as F09a?’3, H10a?’0, H12a?’0, the three parameters can be restored to normal after modification.

          (6) There is no display failure on the operation panel When this fault occurs in the G/P9 Series, the charging resistor or the C19 capacitor of the power driver board may be damaged. If the fault occurs on the inverter of the large-capacity G/P9 series, the internal contact may not be present. Suction caused. For G/P11 small-capacity inverters, in addition to problems with the power supply board, the small circuit board on the IPM module may also be a problem; for a machine with a capacity of 30G11 or more, the power supply board may fail to provide a fuse FUS1 for the main board. No fault on power-up. When the motherboard has a problem, it will also cause power failure.

          Our Driverless LED Flood Light Use Seoul IC drive program, driverless, ultra-high efficiency 125LM / W, PF> 0.9, no EMI electromagnetic interference, 10KV Surge Protection, more than 50000 hours lifespan, 5 years warranty, Mainly used for large-scale workplace mines, building contours, stadiums, overpasses, monuments, parks and flower beds. Available in 40W, 50W, 100W, 150W, 200W, versions.

          Driverless LED Flood Light

          Driverless LED Flood Light,LED Flood Light Driverless,Module LED Flood Light,Flood Light

          Shenzhen Ri Yue Guang Hua Technology Co., Ltd. , https://www.ledlightinside.com

          亚洲 欧美 图片 自拍 视频
          <em id="7lnzx"></em>

            <pre id="7lnzx"></pre>

                <strike id="7lnzx"><address id="7lnzx"></address></strike>

                <big id="7lnzx"></big>